A home security system will keep your family members safe and protected. You can always leave your house with peace of mind, knowing that they are all protected with these technological advancements. However, a professional might not come in right away for installation all the time. That’s why it is important to know how to install security camera wiring when that time comes.
When home security is malfunctioning, it can either be broken, or a rat munched onto the wirings. That’s when your expertise might come in handy because your home becomes susceptible to burglars and break-ins. In this article, I’ll teach you the basic steps on how to install security cameras with wires. You don’t need professional expertise to do this, you will only need to follow the procedures, and you are good to go.
Things to Consider When Installing Security Camera Wiring
If you aren’t very adept at doing your DIY tricks installing a home security camera, then it would be quite daunting for you. Following poorly instructed manuals doesn’t help at all. Learning how to install security camera wiring requires you to drill holes, run cabling, and connect every piece of wire in order.
Installing home security wiring will be different; however – if you are reading this guide, your chances of successfully installing it is great. Just a simple tip, if you don’t want to go through all the hassles of wiring your home security system, then you might just want to opt for a battery-powered security system.
The things you will need are:
- Electrical Wires
- Electric Drill
- Electrical Tape
If you install an outdoor home security camera, you will likely need to run the electrical wirings through the house. This means that you are typically running wires from ceiling, walls, and other hard to reach areas. That’s why it is easy for people to lose patience and mess everything up.
It would help if you planned out everything. Spending 15 to 30 minutes planning will save you countless hours. The main thing you need to consider is where you are placing the central hub – the central hub contains the DVR, hard drive, and screen.
Once the decision has been made, then you need to find the right place for your camera. After planning where to place your camera effectively, you will be planning the most effective route of your wires and onto the central hub. In most cases, you may want to run your wires from a single location near your central hub. You can now get down to the main part, which is learning how to install security camera wiring.
Tips When Installing Security Camera Wiring
Perhaps, you are eager to know how to install security camera wiring. But before you start, it is important to turn off the main power supply because we are associating ourselves with the electricity. When you’ve planned where the route of the wire will be, drill a hole onto these places and then use a hanger for your wires, this is to make sure that there are no obstructions.
Ensure that the holes are a little wider than the wirings because they are intended for the wirings to pass through wider holes just in case you are going to add more wires and security cameras in the future. Another tip is labeling your wires so you know which wire needs to go where.
Steps on How to Install Home Security Wiring
If you have arrived at this step already, you will most likely install your camera and place it in the best location possible. Once done, everything would be simple from here on out. These are the steps on how to install security cameras with wires.
Step 1
If you haven’t placed your camera on their location, install them. It will only take a screwdriver and nuts to install them.
Step 2
The next step would be drilling holes for your wires to pass through. Be sure that the holes are intended for the wires to pass through to reach the central hub with ease.
Step 3
When you’ve successfully drilled a hole, and the wires run from the camera to the router, install wire guards. This is to prevent rats from chipping your wires.
Step 4
After running all the wires from the camera to the routers, conceal the holes. If you aren’t concealing them, moisture can buildup and get right through the connections, leading to more headaches.
Step 5
Fill the holes with waterproof materials such as duct seal or silicone.
Step 6
When your camera is already installed, it would be best to protect from it tampering from humans or animals by installing wire guards. These are a cheap and effective way to protect your camera.
How to Hide Security Wires Inside your Home
If you don’t want to ruin your home’s décor, you can try these quick and easy steps to hide security wires.
- Solution 1: When you drill holes for your wires to pass through, you can easily hide them using wire guards. They are more aesthetically pleasing to the eyes rather than the wires itself.
- Solution 2: Loose wires are very unsightly. Painting them is a good choice, or use staple wires and run them into corners and paint them afterward.
- Solution 3: Run the Home security wiring in your attic – the best way to conceal wires.
- Solution 4: Another great option is to let your run wires from plastic pipes or PVC pipes; this allows them to be concealed entirely and protects them from external damages, rats, and dust.
Conclusion
Planning on how to install security camera wiring is a must, especially for homeowners who don’t like seeing loose wires from the ceiling. Installing home security wiring might be a daunting task for you, but reading all the things here will surely give you a good idea of how to install.
Lastly, these are just pretty basic and easy to do steps. You’ll never have to worry again. Fully functional home security is like a fortress, burglars and thieves can’t go unnoticed! Find out more about security cameras.